【 Weak current College 】 installed electric curtains motor steps with rail

First step: draw line location, measured rail dimensions

1. draw line positioning accuracy is installed curtain track key, first measure good fixed pitch, and the desired dimensions of the installation of the orbit;

2. the customer's size should be measured as the total length of the track;

3. track overall length as the main gear box (motor), track length, Deputy of the gear box (shown in Figure 1);



4. curved track, may, in accordance with building radians bend arc type of curtain track (Note: radian shall not be less than 120 °)

About arc type curtain track measurement methods:

1. arc type road Press picture, and indicate "A" and "B" and "C" length and angle of the arc-shaped rail, and indicate the location of the main transmission gearbox, single-drive or dual-drive (Note: the "A" and "B" length contains main gearbox and Deputy transmission box length) (Figure 2)



2. for viewing platform, the radial road, by drawing out and indicate (chord), (ARC), (ARC). And indicate the location of the main transmission gearbox. Single-drive or dual-drive, the size is the track or external dimension in the dimension. (Note: the arc length contains main gearbox and Deputy transmission box length) (fig. 3)



Step 2: installing lifting clamp

Will clamp rotated 90 ° and rail links, with self-tapping screws lifting clamp installed on the roof (like a concrete structure, needed to be expansive products to be silk.

Step three: electrical wiring



(Note: two-machine connection please refer to product specifications)

Step 4: motors and rail join

Specialized complex motor using crawler curtain track ends fitted with gearbox, and motor-gear box is connected to the other end as Deputy gearbox. Specific actions are as follows:

1. put the power of 90 ° to the master gear box; (Note: the main gearbox of the flat rotation axis and motor interface to match)

2. the motor rotates 90 ° clockwise;

3. rotating in place, the plate is pushed into the gearbox to the limit position, will be automatically locked, motor and gearbox connection OK; finished edge connection. (Note: missed good may not power up, so as not to damage the motor)

Step five: motor travel regulation

Motor trailer is equipped with a micro switch gear and equipment, motor wiring requirements for forward and reverse, thereby achieving the curtains open and closed stroke self positioning. Stroke setting as follows:

1. adjust the stroke before motor and orbital separation of transmission case, so that the orbit of fall is in the full open and full closed end. To remove the rear cover of electric motor, you can see about two knobs;

2. knob (1) and (2) there is a locking plate, locking piece dial to the knob (2), the knob (1) push, from transparent shell you can see the gear from the tooth and status, at which point the fingers rotate knob (1) 【 the forward and reverse rotation may 】 makes three slot (the middle one for color ring) slot for a line, you can hear the micro switch "sentries", you can also see the micro switch produces action (corresponding micro switch into short circuit), the knob (1) and gently pull out (do not turn), the gear into the mating status, knob (1) adjustment will come to a close;

3. then adjust knob (2), so the position lock piece dial to knob (1), and push knob (2) to state the gear from the mating,, repeated knob (1) all resizing action, so the position micro switch into short circuit status;

4. the motor mounted on the rail of the transmission case, push the latch plate fixed gear box. Powered by the controller switches for electrical power, the lock piece dial to knob (1); the knob (2) push and slightly 【 the forward and reverse rotation may 】 knob (2); curtains for opening or closing movement, to achieve the required location, they immediately cut off the power to the motor, gently pull the application button (2), bringing the gear into the position of teeth in-;

5. through the controller switches the motor operation operated directional control, so that the lock piece to the knob (2) the knob (1) push and slightly 【 positive and negative direction may 】 immediately cut off the power to the motor, gently pull out the knob (1), the gear into the position of teeth in-;

6. knob (1) and (2) are tooth-transmission status, adjust the work will come to a close;

7. products to be used for the back cover and tighten the screws, locking plate is fixed.